Nordson Encore HD iControl System Page 55 Hardware Manual Download

Page: 55 / 93

Troubleshooting

4-15

Part 1603054-02

2015 Nordson Corporation

Correction

Message/Condition

Error

Code

907

TCP port already bound

Programming error. Contact Nordson technical support.

908

Listen failed

Programming error. Contact Nordson technical support.

909

File descriptors

exceeded

Programming error. Contact Nordson technical support.

910

No permission to

access serial or TCP

port

Programming error. Contact Nordson technical support.

911

TCP port not available

Programming error. Contact Nordson technical support.

917

Checksum error

Noise in network. Check for loose connections or Ethernet cables

routed parallel to high voltage or VFDs.

918

Invalid frame error

Noise in network. Check for loose connections or Ethernet cables

routed parallel to high voltage or VFDs.

919

Invalid reply error

Noise in network. Check for loose connections or Ethernet cables

routed parallel to high voltage or VFDs.

920

Reply time-out

Noise in network. Check for loose connections or Ethernet cables

routed parallel to high voltage or VFDs.

921

Modbus exception

response

Programming error or remote hardware error. Check node

functions. Refer to manufacturer manual for troubleshooting.

925

Illegal Function

exception response

Programming error or remote hardware error. Check node

functions. Refer to manufacturer manual for troubleshooting.

926

Illegal Data Address

exception response

Programming error or remote hardware error. Check node

functions. Refer to manufacturer manual for troubleshooting.

927

Illegal Data Value

exception response

Programming error or remote hardware error. Check node

functions. Refer to manufacturer manual for troubleshooting.

928

Slave Device Failure

exception response

Programming error or remote hardware error. Check node

functions. Refer to manufacturer manual for troubleshooting.

−

Watchdog Fault

(any remote node

controller fault)

Control program in remote node controller is not running, or

controller has no program installed.

NOTE:

This fault may be a normal response to removing electrical

power from the remote node.
Check the remote node controller mode selection switch. The

switch should be in the run position.
Replace the remote node controller. The replacement must be

pre-programmed or a program must be downloaded and installed in

the field.
Contact Nordson technical support for details.

−

Operation was

successful

Normal operation. No action required.

−

Illegal argument error

Programming error. Contact Nordson technical support.

−

Illegal state error

Programming error. Contact Nordson technical support.

−

Evaluation expired

Programming error. Contact Nordson technical support.

−

I/O error class

Programming error. Contact Nordson technical support.

Fieldbus protocol error

class

Programming error. Contact Nordson technical support.

Obsolete

Summary of Contents for Encore HD iControl System






























































































Search results

Summary of Contents for Encore HD iControl System

Reviews:

Related manuals for Encore HD iControl System

Brands by name

Popular brands

Nordson Encore HD iControl System, Hardware Manual

Search results

Summary of Contents for Encore HD iControl System

Reviews:

Related manuals for Encore HD iControl System

Brands by name

Popular brands