Nordson Encore HD iControl System Page 74 Hardware Manual Download

Page: 74 / 93

Troubleshooting

4-34

Part 1603054-02

2015 Nordson Corporation

Testing Ethernet Cables

A typical Ethernet cable test device consists of two separate units: a main

unit and a remote unit. Use the main unit alone to test patch cables and

both units to test cables after pulling them through conduit and connecting

them to the termination modules.

Local Test

−

Patch Cables

1. Connect both male RJ45 connectors to the main unit.
2. Turn the unit on. A red LED will blink indicating a test in progress.
3. Watch the cable test LEDs. If all are green, then the cable is good. If

one or more flash red, then the cable is faulty and must be replaced.

Remote Test

−

Cable Run

1. Connect one end of a previously tested patch cable into the termination

module connected to the cable run. This provides you with two RJ45

male connectors on the cable run to connect to the test unit.

2. Plug the other end of the patch cable into the remote unit.
3. Plug the RJ45 male connector at the network interface end of the cable

run into the main unit of the cable tester.

4. Turn the main unit on.
5. Watch the cable pair LEDs on the remote unit.

If all LEDs are green, then the cable run is good.

If one or more LEDs flash red, then either the termination module
connections are miswired or incomplete, or the cable is faulty.

Make sure the cable connections to the termination module are correct.

Check each connection. If you suspect a bad connection, you can pull the

lead out of the module and punch it down again closer to the jacket.

If the termination module connections are good, then the cable is faulty and

must be replaced.

Obsolete

Summary of Contents for Encore HD iControl System






























































































Search results

Summary of Contents for Encore HD iControl System

Reviews:

Related manuals for Encore HD iControl System

Brands by name

Popular brands

Nordson Encore HD iControl System, Hardware Manual

Search results

Summary of Contents for Encore HD iControl System

Reviews:

Related manuals for Encore HD iControl System

Brands by name

Popular brands