Nordson Encore HD iControl System Page 91 Hardware Manual Download | Manualshive

Page: 91 / 93

background image

DOC14039-03

EU DECLARATION of CONFORMITY

Product: Encore HD Automatic Powder Spray System

Models:

Encore HD Automatic Applicator and Encore HD iControl 2

Description:

This high density, automatic electrostatic powder spray system includes applicator, control

cable and associated controllers. These controls are available in a 4 - 32 applicator control cabinets as a
main console with a pc and display or an auxiliary console without the pc or display. There is an optional
Pedestal unit for remote mounting of the display within the hazardous zone or classified area.

Applicable Directives:

2006/42/EC - Machinery Directive
2014/30/EU - EMC Directive
2014/34/EU - ATEX Directive

Standards Used for Compliance:

EN/ISO12100 (2010) EN60204-1 (2006) EN61000-6-3 (2007) FM 7260 (1996)
EN60079-0 (2013)

EN50050-2 (2013) EN61000-6-2 (2005)

EN60079-31 (2014)

EN50177 (2009)

EN55011 (2009)

Type of Protection:

- Ambient Temperature: +15ºC to +40ºC
- Ex II 2 D / 2mJ = Auto Applicators
- Ex II (2) D = Main Console and Auxiliary Console Controllers
- Ex II (2) 3 D = Optional Pedestal

ATEX Product Certificates:

- FM13ATEX0006X (Applicators) (Norwood, Mass. USA)
- FM16ATEX0055X (Controllers) (Norwood, Mass. USA)

ATEX Quality System Certificate

- 1180 Baseefa (Buxton, Derbyshire, UK)

___________________

Date:

09 Sept 2017

Vance Wilson
Engineering Manager
Industrial Coating Systems
Amherst, Ohio, USA

Nordson Authorized Representative in the EU
Person authorized to compile the relevant technical documentation.
Contact:

Operations Manager

Industrial Coating Systems

Nordson Deutschland GmbH

Heinrich-Hertz-StraBe 42-44

D-40699 Erkrath

Obsolete

«
...
89
90
91
92
93
»

Summary of Contents for Encore HD iControl System






























































































Reviews:

No comments

Related manuals for Encore HD iControl System

Brand: Yamaha Pages: 50

Brand: A&D Pages: 30

Brand: Baoding Longer Precision Pump Pages: 6

Brand: Paia Pages: 11

Brand: CAB Pages: 39

Brand: CAB Pages: 27

Brand: Gaspardo Pages: 196

Brand: RAB Pages: 2

Brand: Xycom Pages: 99

Brand: Hagerman Pages: 4

Brand: hager Pages: 2

TECSHOW QUAD SPIDER 60

Brand: Ampro Pages: 9

Brand: Launch Pages: 3

Brand: Launch Pages: 43

Brand: Launch Pages: 8

Brand: Launch Pages: 67

Brand: Launch Pages: 55

Brand: LAUNCH TECH Pages: 14

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands