Nordson Encore HD iControl System Hardware Manual Download Page 76

Page: 76 / 93

Repair

5-2

Part 1603054-02

2015 Nordson Corporation

CAUTION:

The gun control cards are electrostatic sensitive devices (ESD).

To prevent damage to the cards when handling them, wear a grounding

wrist strap connected to the iControl enclosure or other ground. Handle the

cards only by their top and bottom edges.

See Figure 5-3. Gun control cards (2) are installed in the card cage from

left to right. Each card controls two guns: the bottom receptacle on the card

is the odd gun number; the top receptacle the even gun number.

To remove a card, unplug the gun harnesses from the card receptacles (3

and 4), pull down the locking tab (5), then pull the card out of the card cage.

To install a new card, slide the card into the slots in the card cage and seat

the card’s finger board firmly into the connector slot on the backplane (6).

Push the locking tab up to lock the card into the card cage. Connect the

gun harnesses to the card receptacles.

Figure 5-3

Gun Control Card Replacement

1. Card cage (slot 1)
2. Gun control card

3. Gun 2 receptacle
4. Gun 1 receptacle

5. Locking tab
6. Backplane

Obsolete

Summary of Contents for Encore HD iControl System






























































































Search results

Summary of Contents for Encore HD iControl System

Reviews:

Related manuals for Encore HD iControl System

Brands by name

Popular brands

Nordson Encore HD iControl System, Hardware Manual

Search results

Summary of Contents for Encore HD iControl System

Reviews:

Related manuals for Encore HD iControl System

Brands by name

Popular brands