Nordson Encore HD iControl System Page 75 Hardware Manual Download

Page: 75 / 93

Repair

5-1

Part 1603054-02

2015 Nordson Corporation

Section 5

Repair

WARNING:

Allow only qualified personnel to perform the following tasks.

Follow the safety instructions in this document and all other related

documentation.

CAUTION:

Do not turn off console power without first performing a program

shutdown. Doing so could corrupt the iControl program and operating

system on the program card. Refer to

Program Shutdown

in the

Configuration

section of the

iControl Operator Interface

manual for the

shutdown procedure.

WARNING:

Hazardous voltages exist within the iControl console. Unless

power must be on to test circuits, always shut off and lock out power before

opening the console to make repairs. All repairs should be made by a

qualified electrician. Failure to observe this warning could result in personal

injury or death.

Repair consists of removing malfunctioning components and replacing them

with new ones. There are no components inside the cabinet that can be

repaired by the customer.

Refer to the wiring diagrams in Section 7 for connections.

WARNING:

Whenever replacing a component that interfaces with the

exterior of the cabinet, such as a gun harness receptacle, make sure that

the dust-tight intergrity of the cabinet is intact by installing the correct

gaskets and seals. Failure to maintain the dust-tight integrity of the cabinet

could invalidate agency approvals and create a hazardous condition.

Gun Control Card Removal/Installation

WARNING:

Shut off console power before removing and installing gun

control cards. Failure to observe this warning could result in damage to the

cards, and could result in personal injury or even death.

CAUTION:

Do not turn off console power without first performing a program

shutdown. Doing so could corrupt the iControl program and operating

system on the program card. Refer to

Program Shutdown

in the

Configuration

section of the

iControl Operator Interface

manual for the

shutdown procedure.

Obsolete

Summary of Contents for Encore HD iControl System






























































































Search results

Summary of Contents for Encore HD iControl System

Reviews:

Related manuals for Encore HD iControl System

Brands by name

Popular brands

Nordson Encore HD iControl System, Hardware Manual

Search results

Summary of Contents for Encore HD iControl System

Reviews:

Related manuals for Encore HD iControl System

Brands by name

Popular brands