Nordson Encore HD iControl System Page 13 Hardware Manual Download

Page: 13 / 93

System Overview

2-1

Part 1603054-02

2015 Nordson Corporation

Section 2

System Overview

iControl System Manuals

This manual covers the iControl console and system hardware for

Encore

systems, used with Encore HD spray guns only.

iControl manuals are organized as follows:

Operator Interface Manual

for all versions of the system, covering

configuration, preset setup, and operation using the iControl software:

1056418

Operator Card

for all versions:

1024758

and this manual.

An Encore HD iControl system console controls up to 32 automatic guns.

Figure 2-1

Prodigy iControl Console

Obsolete

Summary of Contents for Encore HD iControl System






























































































Search results

Summary of Contents for Encore HD iControl System

Reviews:

Related manuals for Encore HD iControl System

Brands by name

Popular brands

Nordson Encore HD iControl System, Hardware Manual

Search results

Summary of Contents for Encore HD iControl System

Reviews:

Related manuals for Encore HD iControl System

Brands by name

Popular brands