Nikon JAA79551 Repair Manual Download Page 34

Page: 34 / 115

INC

JAA79551-R.3690.A

- Ａ 7・AF-S VR 70-300/4.5-5.6G -

・

Attach the light-shielding sheets (#141 and #142) on the lead groove ring.

�

[#141] and [#142] have the adhesive double-coated tape attached.

）

#141

#142

①

Mount the rotary tube on the lens stand (

★

J11338) [With the rotary

tube being mounted, this lens stand is used until the assembly of

the front fixed-tube (i.e.

④

of Page A9) ]

②

Get the marked "A" part of the 2nd lens-G holding tube to come

to the cutout-side of the lead groove ring. Then lift and slide only

the rotary tube, and mount the 2nd lens-G holding tube by fitting

its three projections in the three straight grooves of the lead groove

ring.

③

While lift and slide only the rotary tube, mount the 3rd lens-G

holding unit by fitting its three projections in the three straight

grooves of the lead groove ring.

part

Cutout

★

: New tool

Light-shielding sheet

★

J11338

★

J11338

Lead groove ring

3rd lens-group holding tube unit

3rd lens-G holding tube unit

2nd lens-G holding
tube

Rotary tube

Summary of Contents for JAA79551




















































































































Search results

Summary of Contents for JAA79551

Reviews:

Related manuals for JAA79551

Brands by name

Popular brands

Nikon JAA79551, Repair Manual

Search results

Summary of Contents for JAA79551

Reviews:

Related manuals for JAA79551

Brands by name

Popular brands