Nikon JAA79551 Repair Manual Download Page 69

Page: 69 / 115

INC

JAA79551-R.3690.A

- Ａ 42・AF-S VR 70-300/4.5-5.6G -

VR ADJUSTMENT

When performing the VR adjustment, please refer to the [Instruction Manual] attached to the VR lens adjustment
equipment (J15380).

Preparation for the VR adjustment

　①

Set up the VR lens adjustment equipment (J15380) as shown in Figure below.

　②

Connect the personal computer to the equipment and run the personal computer.

　③

Mount the lens on the equipment. Set the focus ring to the infinity position and the zoom ring to TELE side.

Please refer to the next page for the procedure to mount the lens.

WARNING

●

This equipment uses the laser beam.

Do not look into the laser beam directory.

Notes:

The distance from the laser beam outgoing port to the radiation face should be about 5m apart.

Do not intercept the optical path of the laser beam.

RS232C cable

Laser beam outgoing port

VR lens adjustment equipment

（

J15380

）

Personal computer

Laser beam

Power switch

「

SERVO

」

switch

「

VIBRATION

」

switch

Summary of Contents for JAA79551




















































































































Search results

Summary of Contents for JAA79551

Reviews:

Related manuals for JAA79551

Brands by name

Popular brands

Nikon JAA79551, Repair Manual

Search results

Summary of Contents for JAA79551

Reviews:

Related manuals for JAA79551

Brands by name

Popular brands