Nikon JAA79551 Repair Manual Download Page 66

Page: 66 / 115

INC

JAA79551-R.3690.A

- A39 ･ AF-S VR 70-300/4.5-5.6G -

E terminal

H terminal

E terminal

H terminal

Servo driving time

(4) Inspection of lens-servo time

Make this inspection on both focal length 70mm (W) and 300mm (T).

Select the servo

driving amount respectively. Each lens-servo drive time must be within the standard.

Caution

：

If the MF ring is rotated during inspections, the waveform shows an abnormal value. Do NOT touch

the MF ring during inspections.

This inspection must be made at the following 5 lens positions with the focal length [both 70 mm (W)
and 300 mm (T)].

●

Oscilloscope setting

V/Div

：

Coupling

：

Time/Div

：

20 m Sec

Trigger Mode

：

SGL (S)

Trigger Coupling

：

Trigger Source

：

CH1

Trigger Position

：-4

div

※

The waveforms of E and H terminals have the

forms for going up for start and going down for
start.

Servo driving time

Lens inclination

Position of index window

Horizontal

Up, right and left

Front lens group 90° angle upward

Front lens group 90° angle downward

(Lens position in inspecting)

Summary of Contents for JAA79551




















































































































Search results

Summary of Contents for JAA79551

Reviews:

Related manuals for JAA79551

Brands by name

Popular brands

Nikon JAA79551, Repair Manual

Search results

Summary of Contents for JAA79551

Reviews:

Related manuals for JAA79551

Brands by name

Popular brands