Nikon JAA79551 Repair Manual Download Page 52

Page: 52 / 115

INC

JAA79551-R.3690.A

- Ａ 5・AF-S VR 70-300/4.5-5.6G -

①

Rotate the zoom ring, and align the screw hole of the cam ring with the hole of the zoom cover ring.

②

Fit the two zoom coupling levers (#65) into the holes of the zoom cover ring, and tighten four screws

(#125).

#125).

③

Attach the two cover sheets (#126).

#125×2

#65

#125×2

#65

#126

Adhesive:

Screw lock

③

Align the position of "300"-mark approx. 1-cm away to the right from the zoom index. Then assemble the

zoom ring into the lens body, and rotate in the direction of the arrow A.

Index

Ａ

Grease: MZ-800S
Apply to the overall sliding
surface with the zoom ring
unit.

Grease: GP-1RS

Apply to the overall groove of the zoom
ring unit.

Lens body

Zoom ring

Zoom coupling lever

Zoom cover ring

Adhesive:

Screw lock

Summary of Contents for JAA79551




















































































































Search results

Summary of Contents for JAA79551

Reviews:

Related manuals for JAA79551

Brands by name

Popular brands

Nikon JAA79551, Repair Manual

Search results

Summary of Contents for JAA79551

Reviews:

Related manuals for JAA79551

Brands by name

Popular brands