Nikon JAA79551 Repair Manual Download Page 36

Page: 36 / 115

INC

JAA79551-R.3690.A

- Ａ・AF-S VR 70-300/4.5-5.6G -

①

Mount the 1st lens-G tube on the lead groove ring by aligning the index (of the 1st lens-G tube) with the

cutout (of the lead groove ring).

#121×3

④

Put the roller

(#75: A

～

D) and the roller (#76: A

～

D) at three places through the cam groove of the front

fixed-tube, then fix these with the nut (#74) at three places.

⑤

Remove the body from the lens stand (

★

J11338).

Apply to the overall contacting surface
with the cam ring.

1st lens-group tube

#74×3

#76:A

～

D×3

#75

～

D×3

Caution:

Align the direction of the nut and reference lines

as below. Then, push the nut (#74) all the way

seated at three places .

#74

Cutout of the lead groove ring

Index

Grease: MZ-800S

Adhesive: Lock end B

Mounting of 1st lens-group tube

Then tighten three screws (#121).

#145A×2

Caution:

The two washers (#145A) are attached

at the positions of the picture.

★

: New tool

Summary of Contents for JAA79551




















































































































Search results

Summary of Contents for JAA79551

Reviews:

Related manuals for JAA79551

Brands by name

Popular brands

Nikon JAA79551, Repair Manual

Search results

Summary of Contents for JAA79551

Reviews:

Related manuals for JAA79551

Brands by name

Popular brands