Nikon JAA79551 Repair Manual Download Page 61

Page: 61 / 115

INC

JAA79551-R.3690.A

- A34 ･ AF-S VR 70-300/4.5-5.6G -

●

AF-S VR70-300 inspection program

(1) Menu screen

・

Menu items

The items 1 and 2 are used for adjustments.

The item 3 is used for reading and writing EEPROM DATA.

"Store & Restore the EEPROM DATA" on sub-menu 5 is for backing up all the data on EEPROM value

in the lens, and for writing the backuped files into the lens. (This is not used for regular repairs.)

The items 4~7 are used for inspections.

・

Selection items

After selecting items screens appear, such as the lens selection, the focal length selection, the voltage set-
ting, the inspection mode start.
The screens depend on the items. Follow the instructions

of the personal computer.

・

Initial driving

Drive scanning several times and stop at infinity-end.

Summary of Contents for JAA79551




















































































































Search results

Summary of Contents for JAA79551

Reviews:

Related manuals for JAA79551

Brands by name

Popular brands

Nikon JAA79551, Repair Manual

Search results

Summary of Contents for JAA79551

Reviews:

Related manuals for JAA79551

Brands by name

Popular brands