Nikon JAA79551 Repair Manual Download Page 81

Page: 81 / 115

INC

JAA79551-R.3690.A

- Ａ 54・AF-S VR 70-300/4.5-5.6G -

Please refer to the following chart before performing the VR adjustment for the product of which VR is defective

with the equipment.

STANDARD TO JUDGE THE VR PERFORMANCE

Check

１

Mount the lens to the

usable body

Repeat to press the shutter

release button lightly

・

Set the VR mode to

「ON」

・

Repeat to press the shutter release button lightly a few times while

the half-release timer is ON.

・

Judge from the noise of control.

[Cause]

①

Defect of checksum

②

Broken wire of the VCM

(Both sides)

③

Defect of the mode switch

④

Others

[Countermeasure]

①

Perform the checksum

with the equipment and

then go to the Check 1

②

Confirm the breakage of

the VCM and go to the

Check 1

③

Perform the switch

inspection with the

equipment

④

Go to Check 2

[Cause]

①

Breakage of the VCM

(One side)

②

Adjustment value is

abnormal.

③

Others

[Countermeasure]

①

Confirm the breakage of

the VCM and then go to

Check 1

②

Go to Check 2

③

Go to Check 2

It does not control entirely

It controls only at first

It controls whenever the

half-release is ON

Go on the next page [Check 2]

How is the VR unit control?

Summary of Contents for JAA79551




















































































































Search results

Summary of Contents for JAA79551

Reviews:

Related manuals for JAA79551

Brands by name

Popular brands

Nikon JAA79551, Repair Manual

Search results

Summary of Contents for JAA79551

Reviews:

Related manuals for JAA79551

Brands by name

Popular brands