Nice CLB207, Instructions And Warnings For Installation And Use

Page: 43 / 98

English – 17
English
the characteristics of the OLD one; in other words if the old one is mem-
orised in Mode 1 then the NEW one will also be memorised in Mode 1;
in this case during the memorisation phase press any one key on the
two transmitters. If the OLD radio transmitter is memorised in Mode 2
press the key with the required command on the OLD transmitter and
press the key on the NEW transmitter with which you wish to associate
the new command.
Take the two transmitters and position yourself within the action range of
the automation and follow the following steps:
01. Press the key on the NEW radio transmitter for at least 5 s then
release it.
02.
Press the key on the OLD radio transmitter slowly 3 times.
03. Press the key on the NEW radio transmitter slowly once.
At this point the NEW radio transmitter will be recognised by the control
unit and will take on the characteristics of the OLD one.
Repeat these steps for each new transmitter to be memorised.
9.4.4 - Deleting a radio transmitter
It is necessary to have a radio transmitter to delete it.
If the transmitter is memorised in Mode 1 one single deletion phase is suf-
ficient and at point 3 any key can be pressed. If the transmitter is memo-
rised in Mode 2 a deletion phase must be carried out for each key.
01.
Press the
P1
key
[B]
key (
fig. 22
) on the control unit and hold it
down.
02. Wait until the led P1 [A] ( fig. 22 ) lights up, within three seconds.
03. Press the key on the radio transmitter to be deleted for at least three
seconds. If deletion is successful led P1 will emit five quick flashes. If
led P1
emits one slow flash it means that the deletion has not been
completed because the transmitter is not memorised.
04. To delete other transmitters keep key P1 pressed and repeat step 3
within 10 seconds otherwise the deletion procedure will end auto-
matically.
9.4.5 - Deleting all memorised radio transmitters
This procedure deletes all memorised transmitters.
01. Press the P1 key [B] key ( fig. 22 ) on the control unit and hold it
down.
02.
Wait until the
P1 led [A]
(
fig. 22
) lights up, then wait until it goes off,
then wait until it has flashed 3 times.
03. Release P1 key precisely when the led flashes the third time.
04. Wait about 4s for deletion to be completed, during which the P1 led
will emit quick flashes.
If the procedure is successful after a few moments the led P1 will emit 5
slow flashes.
N M N M FLASH BUS STOP SbS
A
B
22
TABLE 9
1 time “Step-by-Step” command Commands the automation as described in table 3 (Step-by-Step function)
2 times “Pedestrian opening” command Causes partial opening of one or two leaves as described in table 3 (Pedestrian Opening)
3 times “Open only” command Causes the leaves to open (open - stop - open etc.)
4 times “Close only” command Causes the leaves to close (close - stop - close etc.)
5 times “Stop” command Halts the manoeuvre
6 times “Apartment block Step-by-Step”
command
The command has no effect on opening, when closing the command causes the move-
ment to reverse, that is, opens the leaves
7 times “High priority Step-by-Step” command Works also when the automation is locked
8 times “Pedestrian opening 2” command Causes partial opening of leaf M2, equal to halfway
9 times “Pedestrian opening 3” command Causes partial opening of both the leaves, equal to halfway
10 times “Open + lock automation” command Causes an opening manoeuvre and when this is complete, the automation is locked;
the control unit will not accept any command other than “High priority Step-by-Step” and
“Release” of the automation
11 times “Close + lock automation” command Causes a closure manoeuvre and when this is complete, the automation is locked; the con-
trol unit will not accept any command other than “High priority Step-by-Step” and “Release”
of the automation
12 times “Lock automation” command Causes a halt of the manoeuvre and locks the automation; the control unit will not accept
any command other than “High priority Step-by-Step” and “Release” of the automation
13 times Release automation” command Causes automation release and reset to normal operation