Nice CLB207, Instructions And Warnings For Installation And Use

Page: 38 / 98

12 – English
English
FURTHER INFORMATION
––– STEP 9 –––
9.1 - ADVANCED SETTINGS
9.1.1 - Parameter settings via radio transmitter
The radio transmitter can be used to set a number of control unit operat-
ing parameters: there are eight parameters.
1)
Pause time: duration for which the leaves remain open (in the case of
automatic closure).
2)
Pedestrian opening: pedestrian opening mode of the leaves.
3) Motor force: maximum force above which the control unit detects an
obstacle, and reverses the movement.
4) “Step-by-Step (SbS)” function: sequence of movements associated to
each “Step-by-Step” command.
5) Discharging motor 1 when closing: adjusts the length of the “brief
reverse” of the motor after execution of the Close manoeuvre, in order
to reduce the final residual force.
6)
Discharging motor 1 when opening: adjusts the length of the “brief
reverse” of the motor after execution of the opening manoeuvre, in
order to reduce the final residual force.
7) Discharging motor 2 when closing: adjusts the length of the “brief
reverse” of the motor after execution of the Close manoeuvre, in order
to reduce the final residual force.
8)
Discharging motor 2 when opening: adjusts the length of the “brief
reverse” of the motor after execution of the opening manoeuvre, in
order to reduce the final residual force.
TABLE 4
Parameters N° Value Action to perform
SbS input configuration on the control unit 1 Step-by-Step (*) Press T1 once
2 pedestrian opening Press T1 twice
Flash output configuration 1 Flashing light (*) Press T2 once
2 Courtesy light Press T2 twice
3 Gate open indicator Press T2 three times
Motor 1 and Motor 2 discharge in closure 1 No discharge (*) Press T3 once
2 0.1s (Minimum) Press T3 twice
3 0.2s Press T3 three times
4 0.3s Press T3 four times
5 0.4s (Medium) Press T3 five times
6 0.5s Press T3 six times
7 0.6s Press T3 seven times
8 0.7s (Maximum) Press T3 eight times
Motor 1 and Motor 2 discharge in opening 1 No discharge (*) Press T4 once
2 0.1s (Minimum) Press T4 twice
3 0.2s Press T4 three times
4 0.3s Press T4 four times
5 0.4s (Medium) Press T4 five times
6 0.5s Press T4 six times
7 0.6s Press T4 seven times
8 0.7s (Maximum) Press T4 eight times
(*)
Original factory value
TABLE 3
Parameters N° Valore Action: operation to be carried out at step 3 in
the recognition phase
Pause time 1 10s Press T1 once
2 20s (*) Press T1 twice
3 40s Press T1 three times
4 80s Press T1 four times
Pedestrian opening 1 Open 1 leaf halfway Press T2 once
2 Fully open 1 leaf (*) Press T2 twice
3 2 leaves partially opened to 1/4 of the full course Press T2 three times
4 2 leaves partially opened to half of the full course Press T2 four times
Motor force 1 Low Press T3 once
2 Medium low (*) Press T3 twice
3 Medium high Press T3 three times
4 High Press T3 four times
Step-by-Step (SbS) function 1 “Open”, “Stop”, “Close”, “Stop” Press T4 once
2 “Open”, “Stop”, “Close”, “Open” (*) Press T4 twice
3 “Open”, “Close”, “Open”, “Close” Press T4 three times
4 Open only Press T4 four times
(*)
Original factory value