background image

 
Neomatica LLC. Vehicle tracker ADM333BLE GLONASS/GPS. Ver. 1.2  dd 13.07.2019

 

 

41 

 

Command 

Answer 

Parameters 

Description 

37 

HUMIDRANGE X,A,B 

 

X - sensor number from 

BLESENSOR list 

A and B - range limits of 

acceptable humidity. 

Set acceptable range for humidity sensor. 

38 

ANGLERANGE X,A,B,C,D 

 

X - sensor number from 

BLESENSOR list 

A,B 

– lower and upper limits 

for the 

“lower” sensor state. 

C,D 

– lower and upper limits 

for the 

“upper” sensor state. 

Set  the  range  of  lower  and  upper  state  of 

the sensor  

39 

ALARMPERIOD X 

ALARMPERIOD X 

– time in seconds 

Set the period of information packets in an 

alarm mode.   

40 

BLEFUEL 

X,Y

 

 

–cell  number  of  the 

sensors list   

– sensor address 

Binding    BLE  fuel  level  sensor  to  the 

tracker. 

(detailed description in clause 

 6.3.4 Adding 

BLE fuel level sensor in a manual mode and 

viewing the list of added sensors.

)

 

41 

BLEFUELINFO X 

 

–  cell  number  of  the 

BLEFUEL sensors list   

 

Data request from bound fuel level sensors 

(detailed description in clause 

 6.3.4.1 Data 

receiving from connected fuel level sensors 

)

 

Summary of Contents for ADM333 BLE

















































Reviews: