manualshive.com logo in svg

NeoDen 800, User Manual, Page: 35 / 88

Share
Download
NeoDen 800 User Manual Download Page 35

31

According to different components, select the corresponding box selection method:

Non-polar single frame: generally outlining all non-polar capacitance and resistance inspection

frames with specifications within 0402. It can also be used as the inspection frame for
noumenon labeling of other components.

Polar single frame: generally outlining all polar capacitors and resistors with specifications

within 0402. It can also be used for noumenon labeling of other components.

Resistance: indicating making the inspection frame for resistance.

Capacitance:

indicating making the

inspection frame for capacitance.

Solder joint square and solder joint circle: indicate making the inspection frame for wave
soldering joint.

0201 and 0402: indicating making the inspection frame for 0201 and 0402 component

Diode: indicating making the inspection frame for diodes.

Tripod element: indicating making the inspection frame for triodes.

Unilateral leg: indicating making the inspection frame for IC that cannot be completely displayed
on the window-table screen.

SOP: indicating the inspection frame of IC in SOP form. (it can only be used for SOP with

Summary of Contents for 800

























































































Reviews:

No comments