NEO TOOLS 04-616, Manual

Page: 10 / 77

10
* It is noted that in some cases the position of the switch in relation to
the rotation may be different to that described. Reference should be
made to the graphic marks on the switch or the unit housing.
The safety position is the middle position of the direction of rotation
switch (2), which prevents accidental starting of the power tool.
•
The drill/driver cannot be started in this position.
•
This position is used to replace drills or bits.
•
Before commissioning, check that the direction of rotation switch
(2) is in the right position.
Do not change the direction of rotation while the spindle of
the drill/screwdriver is rotating.
ADDITIONAL HANDLE
The drill/screwdriver has a practical handle (10) which is mounted on
the body of the drill/screwdriver for a secure and stable hold while
drilling.
•
The handle is mounted by placing it on the body and tightening it
with the handle.
OPERATION AND MAINTENANCE
Remove the battery from the unit before c a r r y i n g out
any installation, adjustment, repair or operation.
MAINTENANCE AND STORAGE
•
It is recommended to clean the device immediately after each use.
•
Do not use water or other liquids for cleaning.
•
The unit should be cleaned with a dry piece of cloth or blown with
low-pressure compressed air.
•
Do not use any cleaning agents or solvents, as these may
damage the plastic parts.
•
Clean the ventilation slots in the motor housing regularly to prevent
the unit from overheating.
•
Always store the device in a dry place out of the reach of
children.
•
Store the device with the battery removed.
EXCHANGE OF QUICK-ACTION CHUCK
The quick-release chuck is screwed onto the spindle thread of the drill.
- screwdriver and additionally secured with a screw.
•
Set the direction of rotation switch (2) to the centre position.
•
Unclamp the jaws of the quick-action chuck (4) and unscrew the
clamping screw (left-hand thread).
•
Fit the hexagonal spanner into the quick-action chuck and strike
lightly on the other end of the hexagonal spanner.
•
Unscrew the quick-release chuck.
•
Installation of the quick-action chuck is carried out in the reverse
order to its removal.
Any defects should be rectified by the manufacturer's
authorised service department.
TECHNICAL SPECIFICATIONS
RATING DATA
brushless drill/driver with impact 04-616
Parameter Value
Battery voltage 18 V DC
No-load speed range (1st gear / 2nd
gear) 0-480/0-1900 min
-1
Tool holder 13 mm
Maximum torque 100 Nm
Protection class III
Mass 1.52 kg
Year of production 2023
04-616 indicates both the type and the designation of the
machine
NOISE AND VIBRATION DATA
Sound pressure level Lp
A
= 88.49 dB(A) K=
5 dB(A)
Sound power level Lw
A
= 96.49 dB(A)
K= 5 dB(A)
Vibration acceleration value (impact a
h
= 11.21 m/s
2
K=
drilling in concrete)
Vibration acceleration values (metal
drilling) 1.5 m/s
2
a
h
= 2.231 m/s
2
K=
1.5 m/s
2
Information on noise and vibration
The noise emission level of the equipment is described by: the
emitted sound pressure level Lp
A
and the sound power level Lw
A
(where K denotes measurement uncertainty). The vibrations
emitted by the equipment are described by the vibration
acceleration value a
h
(where K is the measurement uncertainty).
The sound pressure level Lp
A
, the sound power level Lw
A
and the
vibration acceleration value a
h
given in these instructions have
been measured in accordance with IEC 62841-1. The vibration
level a
h
given can be used for comparison of equipment and for
preliminary assessment of vibration exposure.
The vibration level quoted is only representative of the basic use of
the unit. If the unit is used for other applications or with other work
tools, the vibration level may change. Higher vibration levels will be
influenced by insufficient or too infrequent maintenance of the unit.
The reasons given above may result in increased vibration
exposure during the entire working period.
In order to accurately estimate vibration exposure, it is
necessary to take into account periods when the device is
switched off or when it is switched on but not used for work.
Once all factors have been accurately estimated, the total
vibration exposure may turn out to be much lower.
In order to protect the user from the effects of vibration, additional
safety measures should be implemented, such as cyclical
maintenance of the machine and working tools, securing an
adequate hand temperature and proper work organisation.
ENVIRONMENTAL PROTECTION
Electrically-powered products should not be disposed of with
household waste, but should be taken to appropriate facilities for
disposal. Contact your product dealer or local authority for
information on disposal. Waste electrical and electronic equipment
contains environmentally unfriendly substances. Equipment that is
not recycled poses a potential risk to the environment and human
health.
"Grupa Topex Spółka z ograniczoną odpowiedzialnością" Spółka komandytowa with
its registered office in Warsaw, ul. Pograniczna 2/4 (hereinafter: "Grupa Topex")
informs that all copyrights to the content of this manual (hereinafter: "Manual"),
including, among others. Its text, photographs, diagrams, drawings, as well as its
composition, belong exclusively to Grupa Topex and are subject to legal protection
under the Act of 4 February 1994 on Copyright and Related Rights (ie Journal of
Laws 2006 No. 90 Poz. 631, as amended). Copying, processing, publishing,
modification for commercial purposes of the entire Manual and its individual
elements, without the consent of Grupa Topex expressed in writing, is strictly
prohibited and may result in civil and criminal liability.
EC Declaration of Conformity
Manufacturer: Grupa Topex Sp. z o.o. Sp.k., Pograniczna 2/4 02-285
Warszawa
Product: Cordless hammer drill/driver
Model: 04-616
Trade name: NEO TOOLS
Serial number
: 00001 ÷ 99999
This declaration of conformity is issued under the sole responsibility of
the manufacturer.
The product described above complies with the following
documents:
Machinery Directive 2006/42/EC
Electromagnetic Compatibility Directive 2014/30/EU
RoHS
Directive 2011/65/EU as amended by Directive
2015/863/EU
And meets the requirements of the standards:
EN 62841-1:2015+A11; EN 62841-2-1:2018+A11;
EN IEC 55014-1:2021; EN IEC 55014-2:2021;
EN IEC 63000:2018
This declaration relates only to the machinery as placed on the
market and does not include components
added by the end user or carried out by him/her subsequently.