manualshive.com logo in svg

NEC SuperScript 1800, User Manual

Share
Download
NEC SuperScript 1800 User Manual Download Page 96

90

SuperScript 1800— User’s Guide

10/100B

ASE

-TX

N

ETWORK

 I

NTERFACE

 U

PGRADE

(Order No. 1805)

A 10/100Base-TX Network Interface Card (NIC) is a device 
for connecting the printer to an Ethernet network. A 
Category 5 network cable is used for interconnecting the NIC 
with the network. The NIC can automatically determine if it 
is connected to a 10-MB or 100-MB network.

The procedure in this section only describes how to install 
the NIC. For information about configuring the printer for 
the NIC, see the NEC SuperScript 1800 Network Configuration 
Guide.

NIC Installation

To install the Network Interface Card:

1.

Remove the printer side cover and access the printer 
Controller Board as described on page 83.

2.

On the back of the printer, remove the two screws from 

the metal back plate (located on Interface Panel), then 

remove plate (A)

. 

3.

Insert NIC into socket on controller board (B) .

4.

Use screw, removed in Step 2, to fasten the card (C).

5.

Use the procedure in Step 1 as guide to replace printer 
side-panel, 500-sheet Cassette, and printer cables.

6.

Connect Category 5 network cable to NIC.

7.

Configure the printer for the NIC as described in the 
NEC SuperScript 1800 Network Configuration Guide.

8.

Confirm the installation by printing a printer 
configuration page as described on page 51.

B

D

A

C

Connect to 
socket on 
controller board

Installing the 10/100Base-TX Network Interface Upgrade

Interface Panel

Summary of Contents for SuperScript 1800




































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands