NEC SuperScript 1800 Page 100 User Manual Download

Page: 100 / 131

SuperScript 1800 — User’s Guide

Paper Jams in the Multipurpose Tray Area

Follow these directions to clear paper jams that occur when a
misfeed happens in the Multipurpose Tray (Tray 1) area.
When this happens the Operator Panel will display

JAM-TRAY

If a paper edge is visible in the feed area, use both hands
to gently pull the paper out of the printer (A).

Remove any remaining paper from the Multipurpose
Tray (B).

Reload the paper back into the Multipurpose Tray (C).

Open the Top Cover (D).

Close the Top Cover (E).

note:

The Top Cover must be opened and closed in

order to clear the paper jam message from the Operator
Panel display.

Summary of Contents for SuperScript 1800




































































































































Search results

Summary of Contents for SuperScript 1800

Reviews:

Related manuals for SuperScript 1800

Brands by name

Popular brands

NEC SuperScript 1800, User Manual

Search results

Summary of Contents for SuperScript 1800

Reviews:

Related manuals for SuperScript 1800

Brands by name

Popular brands