23
123456
123456
123456
123456
123456
123456
SIGNAL ENTRY
.
To make the signal entry, proceed as follows:
1
Press the ADJUST button.
• The “ADJUST” menu is displayed.
NOTE: The projector may ask you to enter your passcode. See
68 for the explanation of the PASSCODE.
2
Use the CURSOR
or
button to highlight the “1/SIGNAL
ENTRY” line and press ENTER.
• The “SIGNAL ENTRY” list will be displayed.
• You can also select the “SIGNAL ENTRY” list directly by
pressing the INPUT “1” button.
3
Use the CURSOR
or
button to select the desired line and
press ENTER.
• The Signal entry menu will be displayed.
NOTE: To advance to the next page or to the previous page,
hold down the CTL button then press the
CURSOR
or
button. To directly access a page, hold down
the CTL button then press any one of the INPUT buttons.
On Signal Entry
The projector uses a micro-processor to automatically read and distinguish between all video signals input at the same time. These
signals are then used to make optimum adjustments for focus, convergence, alignment, etc. Various parameters must be registered
into the micro-processor beforehand to ensure the video signals are recognized and adjusted to optimum quality.
The Signal Entry registers these video signals in the SIGNAL ENTRY list and at the same time obtains the various parameters
pertaining to these signals. Always access this mode first whenever inputting video signals for the first time so that you can register
the video signals before making any adjustments. If the current input signal(s) has not been registered, the “UNREGISTERED
SIGNAL” message is displayed on screen.
NOTE: If you have software which changes scanning mode due to the graphic board of your PC (such as VGA), it will be necessary
to register signal entry for each scanning mode. This can be done using your PC by way of stopping the software in each scanning
mode and performing a signal entry operation.
Signal Entry Procedures
– A D J U S T –
1 / S I G N A L E N T R Y
2 / F O C U S
3 / A L I G N M E N T
4 / C O N V E R G E N C E
5 / K E L V I N
6 / R , G , B G A I N
7 / P A S S C O D E
8 / O P T I O N
9 / R E F . A D J U S T
P 0 1 / 1 0 – 2
S I G N A L E N T R Y
S T A N D A L O N E
N O
0 1
0 2
0 3
0 4
0 5
0 6
0 7
0 8
0 9
1 0
F H
1 5 . 7 4 k H z
1 5 . 7 4 k H z
1 5 . 7 4 k H z
1 5 . 7 4 k H z
4 8 . 6 0 k H z
F V
6 0 . 0 0 H z
6 0 . 0 0 H z
5 0 . 0 0 H z
5 0 . 0 0 H z
6 0 . 0 0 H z
D A T E
0 0 / 0 0 / 0 0
0 0 / 0 0 / 0 0
0 0 / 0 0 / 0 0
0 0 / 0 0 / 0 0
0 0 / 0 0 / 0 0
P 0 1 / 1 0 – 1
S I G N A L E N T R Y
S T A N D A L O N E
N O
0 1
0 2
0 3
0 4
0 5
0 6
0 7
0 8
0 9
1 0
S O U R C E
V I D E O
V I D E O
V I D E O
V I D E O
R G B
I N P U T
A
A
A
A
A
N A M E
N T S C 3 . 5 8
N T S C 4 . 4 3
P A L
S E C A M
V E S A 1 0 2 4
§ ©
Signal name
Input terminal
Entry date
Rgistered input module
Connect condition of the Switcher
Vertical
Frequency
Horizontal
Frequency
Page / total pages – sheet No.
OUTPUT DATA : LIST NO.
✻ ✻
OUTPUT DATA : LIST NO.
✻ ✻
Output data for the signal currently projected.
