manualshive.com logo in svg

Multitech ProxyServer MTPSR1-202ST, User Manual, Page: 37 / 142

Share
Download
Multitech ProxyServer MTPSR1-202ST User Manual Download Page 37

Chapter 4 - ProxyServer Software

37

MTPSR1-202ST

Internet Setup

The Internet Setup dialog box displays the phone number the ProxyServer is going to dial to reach
your ISP, the protocol the ISP supports,  and if you would link the ProxyServer to dial a telephone
when you power on your unit.

The Dial Number field displays the phone number of the ISP you initially assigned during your initial
configuration. If the WAN port is not being used for Internet access, then the Dial Number field should
be blank.

ProxyServer supports Point-to-Point Protocol (PPP) and Serial Line Internet Protocol (SLIP) on the
WAN link. The majority of the time the ISP is going to support PPP. PPP supports two user
authentication protocols;  Password Authentication Protocol (PAP) and Challenge Handshake
Authentication Protocol (CHAP). When you established your Internet account your ISP should have
indicated which protocol it supports.

Your user name and password are displayed in the PPP group for the WAN port which will be
connected to the Internet.  The user name and password were enterred in the Default WAN Link
setup dialog box during the initial configuration.  If the WAN port is not being used for Internet access,
then the User Name and Password fields will be blank.  You can change your User Name and
Password in these fields for the WAN port.

Clicking the Advanced tab brings up the parameters that affect the WAN link.

Summary of Contents for ProxyServer MTPSR1-202ST















































































































































Reviews:

No comments