manualshive.com logo in svg

Multitech ProxyServer MTPSR1-202ST, User Manual, Page: 119 / 142

Share
Download
Multitech ProxyServer MTPSR1-202ST User Manual Download Page 119

Appendixes

119

MTPSR1-202ST

Result Codes

When the ProxyServer receives an AT command from the computer or terminal, it attempts to
execute the command, then sends a status message to the computer or terminal that reports the
result of the command. The ProxyServer provides you with several of these response messages, or
result codes, which can be displayed on your monitor or intercepted and used by your
communications software. Using the V command, you can select whether the result codes are terse
(numbers) or verbose (words).

The ProxyServer’s result codes are listed below. Note that the speed of an ISDN channel is always
either 56 Kbps or 64 Kbps. CONNECT messages indicate the speed of the connection between the
ProxyServer and your computer or terminal.

Terse

Verbose

Definition

0

OK

ProxyServer executed the command without error.

1

CONNECT

ProxyServer has established an ISDN  connection.

2

RING

ProxyServer has detected a ring caused by an incoming call.

3

NO CARRIER

ProxyServer did not detect a carrier within the time allotted by register S7.

4

ERROR

There was an error in the AT command.

5

CONNECT 1200

ProxyServer has connected at 1200 bps.

6

NO DIALTONE

ProxyServer has a poor connection to the ISDN network.

7

BUSY

ProxyServer has detected a busy signal.

8

CONNECT 300

ProxyServer has connected at 300 bps.

10

CONNECT 2400

ProxyServer has connected at 2400 bps.

11

CONNECT 4800

ProxyServer has connected at 4800 bps.

12

CONNECT 9600

ProxyServer has connected at 9600 bps.

14

CONNECT 19200

ProxyServer has connected at 19200 bps.

28

CONNECT 38400

ProxyServer has connected at 38400 bps.

32

CONNECT 48000

ProxyServer has connected at 48000 bps.

17

CONNECT 56000

ProxyServer has connected at 56000 bps.

18

CONNECT 57600

ProxyServer has connected at 57600 bps.

19

CONNECT 64000

ProxyServer has connected at 64000 bps.

20

CONNECT VOICE

ProxyServer has made a voice connection.

57

CARRIER 56000

ProxyServer has detected a 56000 bps carrier.

59

CARRIER 64000

ProxyServer has detected a 64000 bps carrier.

78

SOFTBONDING

ProxyServer is using the SoftBonding protocol.

PROTOCOL

79

PPPC PROTOCOL

ProxyServer is using the Point-to-Point protocol.

96

CHANNEL B1

Channel B1 is in use.

97

CHANNEL B2

Channel B2 is in use.

Summary of Contents for ProxyServer MTPSR1-202ST















































































































































Reviews:

No comments