manualshive.com logo in svg

Multitech ProxyServer MTPSR1-202ST, User Manual, Page: 13 / 142

Share
Download
Multitech ProxyServer MTPSR1-202ST User Manual Download Page 13

Chapter 2 - Installation

13

MTPSR1-202ST

Cabling

The cable connections include the connection for your Ethernet, a short adapter cable to connect to
your PC for software loading, and finally your power connection. If additional RAM needs to be
added, refer to the “Adding RAM” section in this chapter. Figure 2-2 shows the ProxyServer’s
external connections.

10BASE T

ON

OFF

POWER

COMMAND PORT

 PHONE

TTelco

elco

Connection

Connection

Ethernet

Ethernet

Connection

Connection

PC

PC

Connection

Connection

Power

Power

Connection

Connection

ISDN

Optional

Optional

Figure 2-2. Back Panel Connections

1.

Connect the external power supply (included with your ProxyServer) to a live AC outlet. Then
connect the other end to the 6-pin circular DIN POWER connector on the back panel of the
ProxyServer as shown in Figure 2-2.

2.

Connect the ProxyServer to a PC using the short RJ-45 to DB-9 cable provided with your unit.
Connect the RJ-45 plug to the COMMAND PORT on the ProxyServer and the other end to a
serial port (COM1 to COM4) on your PC.

3.

To make the network connection, connect one end of an RJ-45 (UTP) cable to the 10BASE-T
connector on the back of the ProxyServer. Connect the other end of the cable to your LAN.

4.

Connect one end of an RJ-45 cable to the ISDN port on the back of the unit and connect the
other end to the ISDN Telephone Network (Telco wall jack).

5.

Turn on power to the ProxyServer by setting the ON/OFF switch on the back panel to the ON
position. Wait for the Fail LED on the ProxyServer to go OFF before proceeding. This may take
up to two minutes.

At this time the ProxyServer is completely cabled.  Proceed to Chapter 3 to load your software.

Summary of Contents for ProxyServer MTPSR1-202ST















































































































































Reviews:

No comments