Motorola Malux MTM5400 Series Feature User Manual Download

Page: 105 / 133

5.14 Location

Select one of the following:

•

Trunked Mode

— Switches to the mode using infrastructure.

•

Direct Mode

— Switches to the mode without using infrastructure.

•

Repeater Mode

— Switches to the Repeater Mode.

•

Gateway Mode

— Switches to Gateway Mode.

•

TXI Mode

— Select

Activate

to stop sending any radio transmission.

If the radio is in

TXI Mode

, it is not possible to switch from

Direct Mode

Trunked Mode

Repeater Mode

, or

Gateway Mode

Networks

Entering TMO / DMO Mode

5.14 Location

See the GPS Location Service for more information.

GPS Location Service

5.14.1 Viewing Your Position

From the home screen, press MENU key.

Select

More . . . → Location → Position

Scroll to view the results about the last time your location was calculated.

To refresh your position:

• enter

Position

— the radio refreshes its position automatically

• press

Refresh

5.15 Packet Data

The Packet Data (PD) Service allows you to transfer data in a TETRA system using the Internet Protocol (IP).

5-47

Summary of Contents for Malux MTM5400 Series





































































































































Search results

Summary of Contents for Malux MTM5400 Series

Reviews:

Related manuals for Malux MTM5400 Series

Brands by name

Popular brands

Motorola Malux MTM5400 Series, Feature User Manual

Search results

Summary of Contents for Malux MTM5400 Series

Reviews:

Related manuals for Malux MTM5400 Series

Brands by name

Popular brands