MOTO GUZZI Stelvio 1200 NTX Service Manual Download Page 79

Page: 79 / 274

Air temperature sensor - instrument panel

Function

It tells the ambient air temperature to the instru-

ment panel.

Operation / Operating principle

NTC type sensor (resistance sensor, inversely

variable with temperature).

Level in wiring diagram:

Temperature sensors

Location:

•

Sensor: under the instrument panel

•

Connector: under the instrument panel

Electrical characteristics:

•

Resistance at 0°C: 32.5 kOhm +/- 5%

•

Resistance at 25°C: 10.0 kOhm +/- 5%

Pin-out:

1. Voltage 5V

2. Ground connection

Instrument panel

Air temperature sensor failure

DSB 06

Error cause

•

An oil sensor failure is signalled when it is detected that the sensor circuit is open or shorted

to positive

Troubleshooting

•

Check the sensor connector and the instrument panel connector (PINS 10 and 18): If they

are not OK, restore. If OK, check continuity of the pink cable between the sensor connector

and the instrument panel connector PIN 10: if it is not OK, restore the cable harness; if OK,

check the correct sensor resistance: if it is not OK, replace the sensor; if it is OK, check

continuity of the brown cable between the sensor connector and PIN 18 of the instrument

panel connector: If not OK, restore the cable harness; if OK, with key set to ON, check if

there is voltage at the sensor connector PIN 1: if there is no voltage, replace the instrument

panel; if there is approximately 12V, restore the cable harness (there is a short circuit in the

battery). If there is 5V voltage, connect a 10 kOhm resistance to PIN 1 of the sensor con-

nector and to the vehicle ground connection: if, with key set to KEY ON, the voltage

measured upstream the resistance decreases, replace the instrument panel. If voltage con-

tinues to be approximately 5V, restore the pink cable (there is a short circuit at + 5V).

Notes

STELVIO 1200 NTX

Electrical system

ELE SYS - 79

Revente Interdite - Revendita Vietata - Resaling Forbiden - Wiederverkauf Verboten

Summary of Contents for Stelvio 1200 NTX



















































































































































































































































































Search results

Summary of Contents for Stelvio 1200 NTX

Reviews:

Brands by name

Popular brands

MOTO GUZZI Stelvio 1200 NTX, Service Manual

Search results

Summary of Contents for Stelvio 1200 NTX

Reviews:

Brands by name

Popular brands