manualshive.com logo in svg

MOTO GUZZI Stelvio 1200 NTX, Service Manual

Share
Download
MOTO GUZZI Stelvio 1200 NTX Service Manual Download Page 150

•

Mark the piston crown on the exhaust

side so as to remember the refitting po-

sition.

•

Remove the piston.

Fitting the piston

NOTE

THE OPERATIONS DESCRIBED BELOW REFER TO REMOVING ONLY ONE HEAD BUT APPLY
TO BOTH HEADS.

•

The reference on the piston ring must

be facing the piston crown.

•

Fit the piston rings on the piston: - the

oil scraper in the lower slot; - the thicker

smooth ring in the intermediate slot; -

the less thick smooth ring in the upper

slot.

•

The piston rings must be offset at 120°

one from the other.

•

Fit one of the two pin snap rings on the

piston.

•

Lock crankshaft rotation.

Specific tooling

12.91.18.01

 

Tool to lock the flywheel and the

starting ring gear

•

Fit the piston.

NOTE

CHECK THE PISTON DIRECTION ACCORDING TO THE REFERENCES MARKED ON THE PISTON
CROWN. DO NOT ASSEMBLE PISTONS AND CYLINDERS OF DIFFERENT SELECTOR TYPES.

Engine

STELVIO 1200 NTX

ENG - 150

Revente Interdite - Revendita Vietata - Resaling Forbiden - Wiederverkauf Verboten

Summary of Contents for Stelvio 1200 NTX



















































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands