MOTO GUZZI Stelvio 1200 NTX Service Manual Download Page 159

Page: 159 / 274

•

Remove the crankshaft afterwards.

•

Collect the shim washer from inside the

crankcase.

See also

Disassembling the

clutch

Removing the phonic wheel

Disassembling the connecting rod

•

Remove both heads.

•

Remove the cylinders and the pistons.

•

Remove the oil sump.

•

Undo the coupling screws (A) inside

the crankcase and remove the con-

necting rods (B).

See also

Removing the flywheel
Disassembling the piston
Removing the cylinder
Removing the cylinder head

STELVIO 1200 NTX

Engine

ENG - 159

Revente Interdite - Revendita Vietata - Resaling Forbiden - Wiederverkauf Verboten

Summary of Contents for Stelvio 1200 NTX



















































































































































































































































































Search results

Summary of Contents for Stelvio 1200 NTX

Reviews:

Brands by name

Popular brands

MOTO GUZZI Stelvio 1200 NTX, Service Manual

Search results

Summary of Contents for Stelvio 1200 NTX

Reviews:

Brands by name

Popular brands