manualshive.com logo in svg

MOTO GUZZI Stelvio 1200 NTX, Service Manual

Share
Download
MOTO GUZZI Stelvio 1200 NTX Service Manual Download Page 215

Installing

•

Spread a thin layer of lubricating

grease all along the swingarm pin.

•

Fit the ring nut in the swingarm pin and

screw it manually.

•

Working from both sides, grease the

cardan shaft cables with the recom-

mended product from the recommen-

ded products table.

•

Block the swingarm, insert the univer-

sal joint, align the holes and, at the

same time, helped by a second opera-

tor, insert the pin completely.

•

Tighten the swingarm pin.

•

Use the suitable box-spanner to tight-

en the ring nut.

Specific tooling

05.91.26.30

 

Tool for tightening the swingarm

pin ring nut - clutch hub

•

Tighten the two swingarm terminal

screws.

STELVIO 1200 NTX

Chassis

CHAS - 215

Revente Interdite - Revendita Vietata - Resaling Forbiden - Wiederverkauf Verboten

Summary of Contents for Stelvio 1200 NTX



















































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands