manualshive.com logo in svg

MOTO GUZZI Stelvio 1200 NTX, Service Manual

Share
Download
MOTO GUZZI Stelvio 1200 NTX Service Manual Download Page 147

Measuring air gap

•

Undo and remove the two screws and

remove the sensor.

•

Insert a suitable plain washer on the

sensor and note its thickness.

•

Place the sensor on the crankcase and move it until it makes contact with the tone wheel.

•

Measure the clearance between the fixing plate and the crankcase with a thickness gauge.

Subtract the plain washer value from this measurement to obtain the clearance between the

sensor and the tone wheel.

•

Remove the washer and fit the sensor after applying adequate sealing paste on the fixing

plate, then tighten the screws to the prescribed torque.

STELVIO 1200 NTX

Engine

ENG - 147

Revente Interdite - Revendita Vietata - Resaling Forbiden - Wiederverkauf Verboten

Summary of Contents for Stelvio 1200 NTX



















































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands