manualshive.com logo in svg

MOTO GUZZI Stelvio 1200 NTX, Service Manual

Share
Download
MOTO GUZZI Stelvio 1200 NTX Service Manual Download Page 140

•

Place the U-bolt on the rocking levers

making sure the two reference pins

match the seats on the cam tower.

•

Tighten the two screws operating diag-

onally and in stages.

See also

Installing the overhead camshaft

Installing the overhead camshaft

•

Place the bowls in the cam tower, if

those previously removed are refitted

be careful not to interchange them.

•

Place the camshaft with the gear seat

on the dowel side.

•

Place the U-bolt on the camshaft mak-

ing sure the two reference pins match

the seats on the cam tower.

•

Tighten the four screws operating di-

agonally and in stages.

Engine

STELVIO 1200 NTX

ENG - 140

Revente Interdite - Revendita Vietata - Resaling Forbiden - Wiederverkauf Verboten

Summary of Contents for Stelvio 1200 NTX



















































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands