manualshive.com logo in svg

MOTO GUZZI Stelvio 1200 NTX, Service Manual

Share
Download
MOTO GUZZI Stelvio 1200 NTX Service Manual Download Page 43

•

Clamp the clutch pipes with the clutch

switch and the left light switch, making

sure that the fixing part of the lower

clamp faces the inside, to avoid that by

turning the steering the instrument

panel is damaged and the clamp gets

unhooked.

FRONT SECTION

TABLE B

•

Pay attention to the longer cable (1),

which is to be placed to the left, while

the shorter cable (2) is to be placed to

the right.

TABLE C - HEADLIGHT AND TURN INDICATOR

SYSTEM CLAMPS

•

Clamp the right headlight cable (1) and

the right turn indicator (2).

STELVIO 1200 NTX

Electrical system

ELE SYS - 43

Revente Interdite - Revendita Vietata - Resaling Forbiden - Wiederverkauf Verboten

Summary of Contents for Stelvio 1200 NTX



















































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands