manualshive.com logo in svg

MOTO GUZZI Stelvio 1200 NTX, Service Manual

Share
Download
MOTO GUZZI Stelvio 1200 NTX Service Manual Download Page 154

Installing the cylinder head

•

Fit the valves in the head, if previously

removed.

•

Take the left cylinder piston to TDC and

lock crankshaft rotation.

•

Determine the thickness of the gasket

to be fitted between the head and the

cylinder as described in the section:

Shimming system.

•

Place the two dowel pins.

•

Fit the gasket with the correct thick-

ness between the head and the cylin-

der.

•

Fit the left cylinder head.

•

Fit a new O-ring in the spark plug hole.

•

Fit the complete cam cap.

•

Fix the cam cap with the four nuts on

the stud bolts.

Engine

STELVIO 1200 NTX

ENG - 154

Revente Interdite - Revendita Vietata - Resaling Forbiden - Wiederverkauf Verboten

Summary of Contents for Stelvio 1200 NTX



















































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands