manualshive.com logo in svg

MOTO GUZZI Stelvio 1200 NTX, Service Manual

Share
Download
MOTO GUZZI Stelvio 1200 NTX Service Manual Download Page 208

•

Fit a new safety washer.

•

Screw the upper ring nut manually and then slightly tighten the clamps on the plate so as to

align notches on the ring nut.

Specific tooling

AP8140190

 

Tool for steering tightening

•

Rivet the tongues of the new safety washer.

•

Fit the fork upper plate on the stems.

Rear

Removing the rear wheel

•

Support the vehicle rear part using a

suitable stand.

•

Engage the first gear.

•

Undo and remove the four screws, col-

lect the spacers and the dust-protec-

tion ring.

•

Remove rear wheel.

Suspensions

STELVIO 1200 NTX

SUSP - 208

Revente Interdite - Revendita Vietata - Resaling Forbiden - Wiederverkauf Verboten

Summary of Contents for Stelvio 1200 NTX



















































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands