manualshive.com logo in svg

MOTO GUZZI Stelvio 1200 NTX, Service Manual

Share
Download
MOTO GUZZI Stelvio 1200 NTX Service Manual Download Page 111

•

Remove the circlip, the shoulder wash-

er and remove the gear of the first gear,

collect the ball bearing cage.

•

Remove the bearing if necessary.

See also

Disassembling the gearbox

Checking the primary shaft

Measure coaxiality of the main shaft with a dial

gauge and a centring device and replace it if not

complying with specifications.

Characteristic

Shaft coaxiality limit

0.08 mm (0.0031 in)

Check transmission gears for signs of pitting and wear and replace damaged gears if necessary.

Check the gear fitting teeth for cracks, damage and wear and replace those damaged if necessary.

Check the transmission gears movement and, if it is not regular, replace the damaged part.

Checking the secondary shaft

Measure the coaxiality of the transmission shaft

with a dial gauge and a centring device and re-

place it if not complying with specifications.

Characteristic

Shaft coaxiality limit

0.08 mm (0.0031 in)

Check transmission gears for signs of pitting and wear and replace damaged gears if necessary.

Check the gear fitting teeth for cracks, damage and wear and replace those damaged if necessary.

Check the transmission gears movement and, if it is not regular, replace the damaged part.

STELVIO 1200 NTX

Engine

ENG - 111

Revente Interdite - Revendita Vietata - Resaling Forbiden - Wiederverkauf Verboten

Summary of Contents for Stelvio 1200 NTX



















































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands