manualshive.com logo in svg

MOTO GUZZI Stelvio 1200 NTX, Service Manual

Share
Download
MOTO GUZZI Stelvio 1200 NTX Service Manual Download Page 76

that the grey/black cable from PIN 1 of the sensor to PIN 23 of the BROWN connector is

shorted to ground: restore the cable harness.

Clutch lever sensor

Function

It tells the clutch lever position to the control unit.

Operation / Operating principle

If the gear is engaged but the clutch is pulled, i.e. circuit closed to ground, vehicle start-up is enabled

anyway.

Level in wiring diagram:

Start-up enabling switches.

Location:

•

Sensor: under clutch lever

•

Connector: on the sensor

Electrical characteristics:

•

Clutch pulled: closed circuit (continuity)

•

Clutch released: open circuit (infinite resistance)

Pin-out:

1. Voltage 12V

2. Ground connection

AXONE: STATUSES

Clutch

Example value:

Yes/No

The statuses regularly viewed are YES / NO

DIAGNOSIS

Troubleshooting:

•

Indication on Axone always NO: check the correct position of the cable terminals on the

sensor and the correct connection of the cables on the terminals. If they are not correct,

restore the cable harness; if correct, disconnect the two terminals from the sensor and check

continuity to ground of PIN 2 (cable harness side): if there is no continuity, restore the cable

harness; if there is, replace the sensor. Check continuity of the brown/purple cable between

PIN 1 of the sensor and PIN 33 of the BLUE connector, cable harness side: if there is no

continuity, restore the cable harness; if there is, replace the sensor. With the key set to ON,

check that 12 Volt is fed to PIN 33 of the BLUE connector

•

Indication on Axone always YES: disconnect the terminals from the sensor and check if

there is continuity between the two PINS, with clutch released: if there is continuity, replace

Electrical system

STELVIO 1200 NTX

ELE SYS - 76

Revente Interdite - Revendita Vietata - Resaling Forbiden - Wiederverkauf Verboten

Summary of Contents for Stelvio 1200 NTX



















































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands