manualshive.com logo in svg

MOTO GUZZI Stelvio 1200 NTX, Service Manual

Share
Download
MOTO GUZZI Stelvio 1200 NTX Service Manual Download Page 264

•

Remove the four TCEI 8x40 screws (1)

(two on each side)

•

Be careful to collect the four spacer

bushings inside the sump guard.

NOTE

FOR REFITTING, FOLLOW THE PROCEDURE IN THE REVERSE ORDER

Fuel tank

FUEL TANK CAP REMOVAL

•

Open the fuel tank cap.

•

Cover the tank fill opening with a clean

cloth so that no foreign bodies can

come in.

•

Undo and remove the four screws.

•

Remove the cap.

FUEL TANK COVER

•

Remove the rider saddle.

•

Operating from both sides, undo and

remove the three screws.

•

Collect the rubber rings of the rear

screws.

•

Remove the fuel tank cover.

See also

Seat

Bodywork

STELVIO 1200 NTX

BODYW - 264

Revente Interdite - Revendita Vietata - Resaling Forbiden - Wiederverkauf Verboten

Summary of Contents for Stelvio 1200 NTX



















































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands