Mitsubishi Electric s-MEXT-G00 006 Technical Manual Download Page 62

Page: 62 / 128

TM_s-MEXT_ME28relC_00_12_19_EN

Technical manual

TRANSLATION OF THE ORIGINAL INSTRUCTIONS

N. Par. Description

Default

U.M.

Min.

Max.

31.55

Eeprom alarm addressing on digital output [0: A | 1: None | 2: B]

31.56

Maintenance alarm addressing on digital output [0: A | 1: None | 2: B]

31.58

Dirty filters alarm addressing on digital output [0: A | 1: None | 2: B]

31.62

Circuit 1 frost-free protection alarm addressing on digital output [0: A | 1: None | 2: B]

31.67

BMS1 serial offline alarm addressing [0: A | 1: None | 2: B]

31.70

Auxiliary temperature probe alarm address 129 on digital output [0: A | 1: None | 2: B]

31.71

Auxiliary humidity probe alarm address 129 on digital output [0: A | 1: None | 2: B]

31.72

Auxiliary probe offline alarm address 129 on digital output [0: A | 1: None | 2: B]

31.73

ADL On Limit alarm addressing on digital output [0: A | 1: None | 2: B]

31.84

Circuit 1 low pressure probe alarm addressing on digital output [0: A | 1: None | 2: B]

31.85

Circuit 2 low pressure probe alarm addressing on digital output [0: A | 1: None | 2: B]

33.15

PAC-IF013B-E Master offline alarm addressing on digital output (0:A - 1:none - 2:B)

33.15

PAC-IF013B-E Master offline alarm addressing on digital output (0:A - 1:none - 2:B)

33.16

P1 PAC-IF013B-E Master alarm addressing on digital output (0:A - 1:none - 2:B)

33.17

P2 PAC-IF013B-E Master alarm addressing on digital output (0:A - 1:none - 2:B)

33.18

P6 Freezing PAC-IF013B-E Master alarm addressing on digital output (0:A - 1:none - 2:B)

33.19

P6 Overheating PAC-IF013B-E Master alarm addressing on digital output (0:A - 1:none - 2:B)

33.20

P9 PAC-IF013B-E Master alarm addressing on digital output (0:A - 1:none - 2:B)

33.21

E0/E4 PAC-IF013B-E Master alarm addressing on digital output (0:A - 1:none - 2:B)

33.22

E1 PAC-IF013B-E Master alarm addressing on digital output (0:A - 1:none - 2:B)

33.23

E2 PAC-IF013B-E Master alarm addressing on digital output (0:A - 1:none - 2:B)

33.24

E3/E5 PAC-IF013B-E Master alarm addressing on digital output (0:A - 1:none - 2:B)

33.25

E6 PAC-IF013B-E Master alarm addressing on digital output (0:A - 1:none - 2:B)

33.26

E7 PAC-IF013B-E Master alarm addressing on digital output (0:A - 1:none - 2:B)

33.27

Fb PAC-IF013B-E Master alarm addressing on digital output (0:A - 1:none - 2:B)

33.28

PL PAC-IF013B-E Master alarm addressing on digital output (0:A - 1:none - 2:B)

33.29

PU PAC-IF013B-E Master alarm addressing on digital output (0:A - 1:none - 2:B)

33.30

EE PAC-IF013B-E Master alarm addressing on digital output (0:A - 1:none - 2:B)

33.15

PAC-IF013B-E Master offline alarm addressing on digital output (0:A - 1:none - 2:B)

33.31

PAC-IF013B-E Slave 1 offline alarm addressing on digital output (0:A - 1:none - 2:B)

33.32

P1 PAC-IF013B-E Slave 1 alarm addressing on digital output (0:A - 1:none - 2:B)

33.33

P2 PAC-IF013B-E Slave 1 alarm addressing on digital output (0:A - 1:none - 2:B)

33.34

P6 Freezing PAC-IF013B-E Slave 1 alarm addressing on digital output (0:A - 1:none - 2:B)

33.35

P6 Overheating PAC-IF013B-E Slave 1 alarm addressing on digital output (0:A - 1:none - 2:B)

33.36

P9 PAC-IF013B-E Slave 1 alarm addressing on digital output (0:A - 1:none - 2:B)

33.21

E0/E4 PAC-IF013B-E Master alarm addressing on digital output (0:A - 1:none - 2:B)

33.38

E1 PAC-IF013B-E Slave 1 alarm addressing on digital output (0:A - 1:none - 2:B)

33.39

E2 PAC-IF013B-E Slave 1 alarm addressing on digital output (0:A - 1:none - 2:B)

33.40

E3/E5 PAC-IF013B-E Slave 1 alarm addressing on digital output (0:A - 1:none - 2:B)

33.41

E6 PAC-IF013B-E Slave 1 alarm addressing on digital output (0:A - 1:none - 2:B)

33.42

E7 PAC-IF013B-E Slave 1 alarm addressing on digital output (0:A - 1:none - 2:B)

33.43

Fb PAC-IF013B-E Slave 1 alarm addressing on digital output (0:A - 1:none - 2:B)

Summary of Contents for s-MEXT-G00 006

































































































































Search results

Summary of Contents for s-MEXT-G00 006

Reviews:

Related manuals for s-MEXT-G00 006

Brands by name

Popular brands

Mitsubishi Electric s-MEXT-G00 006, Technical Manual

Search results

Summary of Contents for s-MEXT-G00 006

Reviews:

Related manuals for s-MEXT-G00 006

Brands by name

Popular brands