Mitsubishi Electric s-MEXT-G00 006 Technical Manual Download Page 16

Page: 16 / 128

TM_s-MEXT_ME28relC_00_12_19_EN

Technical manual

TRANSLATION OF THE ORIGINAL INSTRUCTIONS

2.4

MAIN LOOP MASKS

The main loop masks have the following functions:

•

Provide a complete overview regarding the status of the unit.

•

Provide useful information to the unit maintenance operator.

2.4.1

List of the main loop masks

Main Mask

Active Functions Mask

Temperature Values Read Mask

Additional T/H Probe Mask

PAC-IF

Summary Mask

Esc

  

Esc

  

PAC-IF Master

Summary Mask

Esc



  

PAC-IF Slave

Summary Mask

  

Gas Pressure Transducers Mask

  

Unit on LAN

Mimic Mask (on Slave Unit)

  

LAN Temperatures

Mimic Mask

  

Unit on LAN

Mimic Mask (on Master Unit)

  

APL Mask

  

ADL Mask

  

Air Flow

Control Mask

  

Air Pressure Differential

Control Mask

  

Direct Freecooling Mask

  

Internal Humidifier Mask

  

Network Transducer Masks

  

GSM Modem Masks

Esc



Esc /



PAC-IF Master

Main Mask

  

PAC-IF Master

Adjustment Mask

  

PAC-IF Master

Temperature Masks

  

PAC-IF Master

Status Mask

Esc

Esc /



PAC-IF Slave

Main Mask

  

PAC-IF Slave

Adjustment Mask

  

PAC-IF Slave

Temperature Masks

  

PAC-IF Slave

Status Mask

Esc

Figure 2-7:

Main menu navigation tree

2.4.2

Main loop mask table

Press

[UP]

[DOWN]

to move from one mask to another.

Below are the main loop masks

Summary of Contents for s-MEXT-G00 006

































































































































Search results

Summary of Contents for s-MEXT-G00 006

Reviews:

Related manuals for s-MEXT-G00 006

Brands by name

Popular brands

Mitsubishi Electric s-MEXT-G00 006, Technical Manual

Search results

Summary of Contents for s-MEXT-G00 006

Reviews:

Related manuals for s-MEXT-G00 006

Brands by name

Popular brands