Minebea CC-Link CSD-892-73 Instruction Manual Download Page 88

Page: 88 / 159

13-6. Con

ﬁ

rmation of load cell output voltage (Monitor mode)

In the con

ﬁ

rmation of the loading cell output voltage, the value in which the load on a present

load cell is converted into mV/V is displayed.
For instance, please execute the calibration by reading the load cell output of tare amount

and weighing capacity by using this function when you use the load cell for the output.

When the load display doesn't indicate a normal value and it doesn't stabilize, the cause

can be divided by the monitoring mode by con

ﬁ

rming each item according to the following

procedures.

When the load display doesn't indicate a normal value

①

Does the output value in the condition to connect a strain gage based transducer

exceed

3.1mV/V?

→

Yes

…

Please advance to

②

→

…

Please calibrate again according to the procedure of [4. Calibration

mode].

②

Does the output value in the condition to be compulsorily short-circuited between

B-D of the upper terminal block exceeds

3.1mV/V?

→

Yes

…

Please inform the details to Minebea.

→

…

The breakdown and the disconnection of the strain gage based

transducer are thought.

When the load display is not steady
    Is the output value in the condition to be the short-circuited between A-F and
    B-C-D-G of the upper terminal block after the strain gage based transducer had been
    removed steady?

→

Yes

…

The in

ﬂ

uence from the noise source such as inverters is thought.

Please contact Minebea when the condition doesn't change even if

you recon

ﬁ

rm the wiring.

→

…

Please inform the details to Minebea.

At such time?

１

By pushing key from the display of ,

the display becomes blinking with a present value of load cell
output voltage.

to EzCTS mode

▲

Please push key after confirming the load cell output voltage.

displays, and the monitor mode is finished.

ENTER

•

The displayed loading cell output voltage value is a reference value. The displayed

accuracy is about 0.5%.

k M

Summary of Contents for CC-Link CSD-892-73
































































































































































Search results

Summary of Contents for CC-Link CSD-892-73

Reviews:

Minebea CC-Link CSD-892-73, Instruction Manual, Page: 88 / 159

Search results

Summary of Contents for CC-Link CSD-892-73

Reviews: