Home
/
Minebea
/
CC-Link CSD-892-73
/
Instruction Manual

Minebea CC-Link CSD-892-73, Instruction Manual, Page: 120 / 159

Share

Page: 120 / 159

Minebea CC-Link CSD-892-73 Instruction Manual Download Page 120

15-3.Shift to condition that can be communicated

The condition that can be communicated is displayed after turning on the power and initial

setting request from the master station.
CSD-892-73 becomes the condition that can be communicated by turning on [Remote

READY (RX(n+7)B)] after completing the initialization with power supply turning on.
The initialization is executed by turning OFF [Remote READY (RX(n+7)9)] when [Initialization

setting request (RY(n+7)9] transmitted from the master station is turned on.
After the initialization is completed, CSD-892-73 responds to the master station by turning on

[Initialization setting response (RX(n+7)9].
[Initialization setting response (RX(n+7)9] is turned OFF and [Remote READY (RX(n+7)B]

is turned on by turning off [Initialization setting request (RY(n+7)9)] after the master station

recognizes ON of [Initialization setting request (RX(n+7)9)]

Timing chart

②

Reading out request

General command request

Request 2 [RYn2]

Command No.

[Response](RWrnE)

Writing/Reading response

(RXn3)

Command No.

(RWwnE)

General command response

(Response 2) [RXn2]

Selection of writing or reading

(R/W) [RYn3]

General data

[RWwnC/D)

Initial data setting request

(RY(n+7)9)

Initial data setting response

(RX(n+7)9)

Remote READY

(RX(n+7)B)

Power supply turning on

109

C

C

-Li

nk

«
...
118
119
120
121
122
...
»

Summary of Contents for CC-Link CSD-892-73
































































































































































Reviews:

No comments