manualshive.com logo in svg

Minebea CC-Link CSD-892-73, Instruction Manual, Page: 6 / 159

Share
Download
Minebea CC-Link CSD-892-73 Instruction Manual Download Page 6

V

5.  Conformity standard

This instrument has suited the following standard. 

EN61326-1

：

2006

 

"Electrical equipment for measurement, control, and laboratory use  

 

－

 EMC requirements"

 

"Immunity test requirements for equipment intended for use in  

 

industrial locations"

•

  Installation place 

Please set up in the control board and the operation panel where EMC solution is 

given.

•

  Power supply 

Please set up the power supply of DC24 V in the control board and operation 

panel where EMC solution is also given. 

The power supply of DC24 V must use "CE applied product".

•

  Cable 

Use the shielded cable other than the power cable.

•

  Shield processing 

Please connect the shield cable of load cell with E terminal in upper terminal 

block.

•

  Please connect the shield cable only for CC-Link interface with SLD terminal in 

the connector for CC-Link interface. 

Please process the shield to the cable for CC-Link and the external I/O surely by 

the conduit piping including the control board.

•

  Grounding 

The ground shall apply the individual ground by using the F.G. terminal in lower 

terminal block.  

Please make the single ground of the instrument, or of the storage case after 

connecting with the storage case when you store only the DC24 V power circuit 

and the instrument in the storage case.  

Please give the earth as a single earth when you store the device other than the 

instrument  in the storage case.

 Caution

•

  At the time of shipment from the factory, the instrument has been plated with a 

clear sheet on the panel sheet for protective purpose. In case of application, use 

the instrument after removing the clear sheet 

fi

rst.

•

  Do not push the panel sheet on the instrument with the excessive strong force nor 

push it with sharp edge object such as a driver. 

•

  If neglected, it may cause damage to the panel switch and even have the 

possibility of damage to resist to environments or operational performances.

•

  When the USB interface is used, the applied CE standard is excluded.

•

  Please observe the following conditions strictly when this instrument suits the below. If 

neglected, it may not conform to the above standard.

Summary of Contents for CC-Link CSD-892-73
































































































































































Reviews:

No comments