manualshive.com logo in svg

Minebea CC-Link CSD-892-73, Instruction Manual, Page: 75 / 159

Share
Download
Minebea CC-Link CSD-892-73 Instruction Manual Download Page 75

UNDER

The value of UNDER is set by set data number SET6.
The output of UNDER is turned on when the measurement result is falling below [FINAL(SET1 

- UNDER(SET6)]
 

Setting range : 00000

～

99999

　　　

：

00000

 

   

Unit : 1D

NEAR ZERO (ZERO BAND)

The output value of NEAR ZERO signal is set by set data number SET7.
The output of NEAR ZERO is turned on when the value of operational target selected by S 

function SF-06 (Comparative operation of ZERO BAND) is falling below the NEAR ZERO 

value.
 

Setting range : 00000

～

99999

　　　

：

00000

 

   

Unit : 1D

FULL

The output value of FULL signal is set by set data number SET8.
The output of FULL is turned on when the value of operational target selected by S function 

SF-07 (Comparative operation of FULL) exceeds the value of FULL.
 

Setting range : 00000

～

99999

　　　

：

00000

 

   

Unit : 1D

　

•

   Please set the stored place to [Internal RAM] when the set data is continuously 

changed, and the rewritable time of [EEPROM] might exceed about on million 

times. 

Please refer [6-10. Changeover of data stored place] for the setting method of 

stored place.

64

Se

ttin

g o

f C

om

par

at

or

Summary of Contents for CC-Link CSD-892-73
































































































































































Reviews:

No comments