Minebea CC-Link CSD-892-73 Instruction Manual Download Page 152

Page: 152 / 159

This lights on with

when the load display exceeds over [(+ Weighing

capacity) + 9D] or [+110 % of the weighing value]. (By the setting of C function

CF-03.)

- OL

This lights on with

when the load display exceeds over [(- Weighing

capacity) - 9D] or [-110 % of the weighing value]. (By the setting of C function

CF-03.)

OVF

Plus over of A/D conversion input. This lights on with

- OVF

Minus over of A/D conversion input. This lights on with

All light on

(When C function CF-15 [Power on ZERO operation is valid.)

All the segments light on when the stability is not detected at turning on the

power. By pushing [FUNC.] key in the condition of all lighting on, the display

becomes the load display compulsorily.

HOLD

This lights on when the power turns on in the condition of HOLD signal ON.

By releasing from the HOLD signal, the display becomes the load display.

141

ific

atio

ns & O

ers

Summary of Contents for CC-Link CSD-892-73
































































































































































Search results

Summary of Contents for CC-Link CSD-892-73

Reviews:

Minebea CC-Link CSD-892-73, Instruction Manual, Page: 152 / 159

Search results

Summary of Contents for CC-Link CSD-892-73

Reviews: