manualshive.com logo in svg

Minebea CC-Link CSD-892-73, Instruction Manual, Page: 148 / 159

Share
Download
Minebea CC-Link CSD-892-73 Instruction Manual Download Page 148

17-2. External control I/O chapter

Event

Please con

fi

rm here.

Reference

A set item of simple 

calibration mode is not 

displayed.

Is not the measurement mode set to 5-steps comparator 

mode?

11-1.

A set item of 5-steps 

comparator mode is not 

displayed.

Is not the measurement mode set to simple calibration mode?

11-1.

The external control 

input doesn't operate.

Do you correctly connect the equipment?

2-5.

Is the allocation of the external control output correctly set?

8-8-1.

Is the signal of 50 ms or more input for the pulse input?

-

Is the signal input at the level input of 50 ms or more 

continuously?

-

The external control 

output doesn't operate.

Do you correctly connect the equipment?

2-5.

Is the allocation of the external control output correctly set?

8-8-2.

Is the setting of measurement value / comparison value within 

the range of setting?

11-2-2. 

11-3-2.

Are the voltage and the electric current for  an open collector 

used within the speci

fi

cation value? 

Vce = DC35 V, Ic = DC50 mA max.

2-5.

The logic of an external 

output is not suitable. 

You want to reverse the 

logic.

Please execute a logical change of the external output.

8-8-3.

17-3. CC-Link interface chapter

Event

Please con

fi

rm here.

Reference

The communication is 

not normal.

Is the cable for CC-Link interface correctly connected?

2-6.

Is the length of the cable for CC-Link interface within the 

regulation that CC-Link society provides?

-

Is the terminating resistance correctly connected?

2-6.

Are the number of occupied station, the station number, 

the baud rate and the method of 32 bit data representation 

correctly set?

14-3-1. 

~ 14-3-4.

You want to con

fi

rm the 

setting station number 

easily.

Please allocate the con

fi

rmation of station number for CC-Link 

interface to F/ENTER key by that operation setting.

8-7.

17-4. USB interface chapter

Event

Please con

fi

rm here.

Reference

The communication is 

not normal.

Is the USB driver installed in the host side? 

Please install after downloading from our homepage.

-

Is the port normally recognized on the host side? 

Please download [USB interface driver install manual] from 

our homepage, and con

fi

rm the details.

16

Is the length of USB cable within  5 m regulated?

-

are the command mode and the stream mode correctly set?

16-2

137

Tro

uble

 Sho

otin

g

Summary of Contents for CC-Link CSD-892-73
































































































































































Reviews:

No comments