Minebea CC-Link CSD-892-73 Instruction Manual Download Page 127

Page: 127 / 159

④

Reading out the condition 1 (Host

→

CSD-892-73)

Terminator

Return (CSD-892-73

→

Host)

Terminator

a : STABLE

[1] = ON, [0] = OFF

b : No use

[0] = Fixed

c : TARE WEIGHT

[1] = ON, [0] = OFF

d : GROSS value

[1] = ON, [0] = OFF

e : NET value

[1] = ON, [0] = OFF

f : ZERO

[1] = ON, [0] = OFF

g : HOLD

[1] = ON, [0] = OFF

h : ERROR

[1] = ON, [0] = OFF

⑤

Reading out the condition 2 (Host

→

CSD-892-73)

Terminator

Return (CSD-892-73

→

Host)

Terminator

a : NEAR ZERO

[1] = ON, [0] = OFF

b : FULL FLOW/S1

[1] = ON, [0] = OFF

c : MEDIUM FLOW/S2

[1] = ON, [0] = OFF

d : DRIBBLE FLOW/S3

[1] = ON, [0] = OFF

e : OVER/S4

[1] = ON, [0] = OFF

f : OK/S0

[1] = ON, [0] = OFF

g : UNDER

[1] = ON, [0] = OFF

h : FULL

[1] = ON, [0] = OFF

Command No.

Operation

Reading out the condition 1

Command No.

Operation

Reading out the condition 1

Space

Condition

Command No.

Space

Condition

Command No.

116

-2

)

Summary of Contents for CC-Link CSD-892-73
































































































































































Search results

Summary of Contents for CC-Link CSD-892-73

Reviews:

Minebea CC-Link CSD-892-73, Instruction Manual, Page: 127 / 159

Search results

Summary of Contents for CC-Link CSD-892-73

Reviews: