26
ENGLISH
STARTING THE PRODUCT
Before starting the product, install the battery pack in the product.
RESTART PROTECTION
The product is supplied with a restart protection.
This prevents the switched-on product from starting by itself when
the battery pack is inserted and from restarting after a switch-o
ff
function of the battery pack.
If the guide bar is outside of the wood, turn o
ff
the product and turn it
on again to continue working.
If the guide bar is inside of the wood wait until the saw chain comes
to a complete stop. Make sure that the switch is in the o
ff
position.
Remove the battery pack from the product and the guide bar from
the cut. Insert the battery pack and then turn on the product again to
continue working.
TRANSPORTATION AND STORAGE
Always lightly oil the chain when storing the product to prevent rust.
Always empty the oil tank when storing to prevent leakage.
Turn o
ff
the product, remove the battery pack, and allow it to cool
before storing or transporting.
Remove all foreign materials from the product. Store the product in
a cool, dry, and well-ventilated place that is inaccessible to children.
Keep away from corrosive agents, such as garden chemicals and
de-icing salts. Do not store the product outdoors.
Fit the guide bar cover before storing the product or during
transportation.
For transportation in vehicles, secure the product against movement
or falling to prevent injury to persons or damage to the product.
CLEANING
Clean dust and debris from openings. Keep the handle clean, dry,
and free of oil or grease. Use only mild soap and a damp cloth to
clean, since certain cleaning agents and solvents are harmful to
plastics and other insulated parts. Some of these include gasoline,
turpentine, lacquer thinner, paint thinner, chlorinated cleaning
solvents, ammonia and household detergents containing ammonia.
Never use
fl
ammable or combustible solvents around tools.
MAINTENANCE
WARNING!
Use only MILWAUKEE accessories and
MILWAUKEE spare parts. Failure to do so can cause possible
injury, contribute to poor performance, and may void your warranty.
Use only MILWAUKEE accessories and MILWAUKEE spare parts.
Should components that have not been described need to be
replaced, contact one of our MILWAUKEE service centres (see our
list of guarantee or service addresses).
WARNING!
Servicing requires extreme care and knowledge
and should be performed only be a quali
fi
ed service technician.
For service, bring the product to the nearest MILWAUKEE service
station for repair. When servicing, use only identical replacement
parts.
WARNING!
Remove the battery pack before adjusting,
maintaining, or cleaning the product. Failure to do so could result in
serious personal injury. Make adjustments or repairs described in
this manual only. For other repairs, contact an authorised service
centre.
Consequences of improper maintenance may cause safety features
to not function correctly, thus increasing the potential for serious
injury.
Keep the product professionally maintained and safe.
Sharpening the chain safely is a skilled task. Therefore, the
manufacturer strongly recommends that a worn or dull chain is
replaced with a new one, available at a MILWAUKEE service centre.
The part number is available in the product speci
fi
cation table in this
manual.
Follow instructions for lubricating and chain tension checking and
adjustment.
After each use, clean the product with a soft, dry cloth.
Remove any chips, dirt, and debris in the battery bay.
Check all nuts, bolts, and screws at frequent intervals for security
to ensure the product is in a safe working condition. Any part that is
damaged should be properly repaired or replaced by a MILWAUKEE
service centre.
REPLACING THE GUIDE BAR AND SAW CHAIN
Wear protective gloves.
1. Remove the bar mounting nut using the combination wrench.
2. Remove the drive sprocket cover.
3. Place the new chain in the correct direction onto the bar and
make sure that the drive links are aligned in the bar groove.
4. Attach the bar to the pruning saw and loop the chain around the
drive sprocket.
5. Reinstall the drive sprocket cover and bar mounting nut.
6. Finger-tighten the bar mounting nut. The bar must be free to
move for chain tension adjustment.
7. Adjust the chain tension. Refer to the “Adjusting chain tension”
section.
8. Hold the tip of the guide bar up and tighten the bar mounting nut
securely.
WARNING!
A dull or improperly sharpened chain can cause
excessive motor speed during cutting that may result in severe
motor damage.
WARNING!
Improper chain sharpening increases the potential
of kickback.
WARNING!
Failure to replace or repair a damaged chain can
cause serious injury.
WARNING!
The saw chain is sharp. Always wear protective
gloves when performing maintenance to the chain.
GUIDE BAR MAINTENANCE
When the guide bar shows signs of wear,
fl
ip the guide bar from
bottom to top on the saw to distribute the wear for maximum bar
life. The bar should be cleaned every day of use and checked for
wear and damage. Feathering or burring of the bar rails is a normal
process of bar wear. Such faults should be smoothed with a
fi
le as
soon as they occur.
Bar rails
A bar with any of the following faults should be replaced.
• wear inside the bar rails which permits the chain to lay over
sideways
• bent guide bar
• cracked or broken rails
• spread rails
Summary of Contents for HEAVY DUTY M18 FHS20
