Miele WCI 320 Operating Instructions Manual Download

Page: 60 / 92

Problem solving guide

Fault message at the end of a programme

Problem

Cause and remedy



Check jet

The pumps are dirty.



Clean the pumps as described in “Problem solving
guide . .”, Opening the door in the event of a
blocked drain outlet and/or power cut“.



Restart the programme after cleaning.

The jet in the top of the door ring is blocked with fluff.



Remove the fluff with your finger. Do not use any
sharp or pointed tools to do this.



Restart the programme after cleaning.

If the fault message appears again, contact Miele.
The washing machine can still be used but with
reduced functionality.

The messages will appear at the end of the programme and when the washing
machine is switched on and need to be confirmed with the

sensor.

Summary of Contents for WCI 320





























































































Search results

Summary of Contents for WCI 320

Reviews:

Related manuals for WCI 320

Brands by name

Popular brands

Miele WCI 320, Operating Instructions Manual

Search results

Summary of Contents for WCI 320

Reviews:

Related manuals for WCI 320

Brands by name

Popular brands