Miele WCI 320 Operating Instructions Manual Download

Page: 66 / 92

Problem solving guide



Clean the drain filters thoroughly.



Remove any foreign objects (e.g.
buttons, coins, etc.) and clean the
interior. Turn the impellers by hand to
check that they rotate freely.



Replace the drain filters correctly (on
the right and left) and tighten them
securely.



Close the drain pump access panel.



Risk of water damage.

Make sure the drain filters are
securely tightened. Otherwise there
is a risk of water leakage during use.
Replace the drain filters correctly and
tighten them securely.

Open the door



Danger of injury due to rotating

drum!
Reaching into a moving drum is
extremely dangerous.
Always make sure that the drum is
stationary before reaching in to
remove laundry.



Use a screwdriver to unlock the door.



Pull open the door.

Summary of Contents for WCI 320





























































































Search results

Summary of Contents for WCI 320

Reviews:

Related manuals for WCI 320

Brands by name

Popular brands

Miele WCI 320, Operating Instructions Manual

Search results

Summary of Contents for WCI 320

Reviews:

Related manuals for WCI 320

Brands by name

Popular brands