Miele WCI 320 Operating Instructions Manual Download

Page: 25 / 92

4. Select programme settings

PowerWash display with the
Quick and Eco sensor controls

If the PowerWash indicator lights up
when you select a programme you can
chose between 3 programme
sequences. The wash result remains the
same.

PowerWash display

For a normal programme sequence.



Do not

activate the Quick or Eco

sensors.

Quick sensor

For a short programme sequence.
Mechanical action and energy increase
with this option.



Touch the Quick sensor.

Eco sensor

For an energy saving programme
sequence. The wash temperature is
reduced and the programme duration
increased.



Touch the Eco sensor.

Tip:

See the following table for a list of

programmes in which the PowerWash
display is active.

Quick

Eco

Cottons



–

Cottons



–

Minimum iron

Delicates

Shirts

QuickPowerWash



–

Dark garments/
Denim

Outerwear

Express 20



–

Sportswear

Automatic plus

Pillows

Curtains

Down filled items

Down duvets

Clean machine



–

X = can be selected

– = cannot be selected



= activated

Summary of Contents for WCI 320





























































































Search results

Summary of Contents for WCI 320

Reviews:

Related manuals for WCI 320

Brands by name

Popular brands

Miele WCI 320, Operating Instructions Manual

Search results

Summary of Contents for WCI 320

Reviews:

Related manuals for WCI 320

Brands by name

Popular brands